Product search

PEX foam staplers secure Uponor PEX to foam board insulation in concrete-slab radiant heating and cooling applications.

PEX rails secure Uponor PEX tubing products to metal and wood support structures.Note: Suitable fastening hardware is required (not included).

PEX stand-up brackets are used in residential slab or commercial multi-floor construction. Secure the bracket to the deck form. Then install the 1/2" PEX tubing in the bracket, either with the 1/2" PEX tubing alone or the 1/2" PEX tubing sleeved inside a corrugated polyethylene carrier tube. The brackets are available in either single- or five-tube configurations.

PEX wall support brackets provide rigid, straight-through support for 1/2" or 3/4" Uponor AquaPEX tubing and 1/2" copper stubs. It features fixed, 2" on-center spacing, and allows the 1/2" Plastic Bend Support (A5250500) to snap into place for 1/2" Uponor AquaPEX tubing as it exits a wall.

Plastic bend supports (glass-reinforced nylon) provide a rigid, 90-degree bend and sleeve for 3/8", 1/2" and 3/4" Uponor PEX tubing. The 1/2" bend support works with PEX wall support brackets (A5750500).

Plastic drop ear bend supports (glass-reinforced nylon) provide a rigid, 90-degree bend and connection-free stub out from a stud wall or floor for 3/8" or 1/2" Uponor PEX tubing.

Use plastic foam staples with Manual Foam Stapler (E6025075) to secure 3/8", 1/2", 5/8" and 3/4" Uponor PEX to rigid foam insulation. Note: Use 1 1/2" Foam Staples (A7015050) for 1" foam and 2 1/2" Foam Staples (A7015075) for 1 1/2" or thicker foam.

Powered zone controllers include transformers for low-voltage operations and relays to operate line-voltage controls. Fully fuse-protected, they also include an isolated end switch and built-in domestic hot water (DHW) priority switch. The indicator lights show full functionality of the products wired to the controllers. A three-amp delay fuse protects four-zone controllers. A seven-amp delay fuse protects six-zone controllers.

Pre-insulated Uponor AquaPEX® complies with the most recent versions of ASHRAE 90.1 and the International Energy Conservation Code (IECC). The product is available with ½" to 1¼" PEX-a service pipe covered in ½" or 1" insulation. The insulation features manufactured-sealed seams running the entire length of the pipe for added convenience and system performance. Check with local code authorities regarding energy-code requirements for specific applications.

Pre-insulated Wirsbo hePEX™ complies with the most recent versions of ASHRAE 90.1 and the International Energy Conservation Code (IECC). The product is available with ½" to 1½" oxygen-barrier PEX-a service pipe covered in ½" to 1½" insulation. The insulation features manufactured-sealed seams running the entire length of the pipe for added convenience and system performance. Check with local code authorities regarding energy-code requirements for specific applications.

Pre-sleeved Uponor AquaPEX® tubing is used in hot and cold water-distribution systems. The highdensity polyethylene (HDPE) corrugated sleeve provides protection for installations in concrete slabs or soil, and allows for removal and replacement of the tubing if required. Note: This tubing can also be used in radiant heating and cooling systems containing no ferrous corrodible components or where ferrous components are isolated from the tubing.

ProPEX brass baseboard elbows connect 1/2", 5/8" and 3/4" Uponor PEX tubing products to 3/4" copper baseboard.Note: ProPEX tool is required. ProPEX rings sold separately.