Digital Controls

- Measures perceived room temperature
- Protection class: IP30
- Color: white glossy

Functions:
- Light indication behind dial after changing the set point
- Heating/cooling demand indication
- Dip switch to enable/disable timer function if timer installed
- Optional: enable/disable timer function

Consisting of:
- Uponor Smatrix Base thermostat standard T-145 Bus POD
- Mounting set

- Measures and displays the perceived room temperature and relative humidity
- Protection class: IP30
- Colour: white glossy

- Functions:
- Heating or cooling demand indication
- RH limit indication
- Individual night setback
- Set time start up wizard
- 6 pre-programmed schedules
- 1 freely programmable schedule
- Cooling allowed function (room by room)
- Displays celsius or fahrenheit
- Operating modes: room temperature (RT), internal with floor max/min (RFT), remote sensor (RS), remote outdoor (RO)
- display with backlight (dims 10 seconds after last button event)
- Displays software version (on power-up)
- Optional: floor or outdoor sensor can be connected

- Consisting of:
- Uponor Smatrix Base thermostat Prog.+RH T-148 Bus
- Mounting set

- Set time start up wizard
- Holiday mode
- Comfort/ECO indication
- Manual H/C switchover function
- 6 pre-programmed schedules
- 1 freely programmable schedule
- ECO setback value setting
- Clock reset
- Timer functions
- Autobalancing de-/activation
- Backlight
- Displays software version on start-up
- Protection class: IP30
- Colour: white glossy

Consisting of:
- Uponor Smatrix Base timer I-143 Bus
- Mounting material

- 4-wire bus cable allows to connect Uponor Smatrix Base / Base PRO devices
- 2 wires for power supply / 2 wires for data transmission
- Shielding: aluminium/polyester foil with tracer strand
- Temperature range: -20°C - +80°C
- Cross section: AWG22
- Sheath: PVC
- Rated voltage: 400VAC/DC

- Suited for Modbus RTU systems
- Supports up to 6 room thermostats and 8 actuators with option to extend to 12 room thermostats and 14 actuators
- (use 1071686)
- Contains data points for heat pump integration
- Max. power input per actuator: 24VAC / 0.2A (0.4A peak)
- Protection class: Class II IP20

- Consisting of:
- Uponor Smatrix Base PRO controller X-148 Modbus RTU
- Quick set-up guide, security instructions
- DIN rail (length: 37cm)
- Mounting material

- Supports up to 6 room thermostats and 8 actuators
- Option to extend up to 12 room thermostats and 14 actuators with 1071686
- Max. power input per actuator: 24VAC / 0.2A (0.4A peak)
- Protection class: Class II IP20
- Colour: grey RAL7015

Consisting of:
- Uponor Smatrix Base PRO controller X-147 Bus 6X
- Quick set-up guide, security instructions
- Micro SD card (pre-inserted)
- DIN rail (length: 37cm)
- Mounting material

- Connects a Uponor Smatrix Base PRO controller X-147 with a BMS or third-party KNX devices
- Power supply: 230VAC (+10%/-15%) / 50/60Hz
- Internal fuse: T5 F3.15AL 250V, 5x20 3.15A quick acting
- Operating temperature: 0°C - +45°C
- Storage temperature: -20°C - +70°C
- Max. consumption: 45W
- Power connection: 1m cable with Europlug
- Connection terminals for system bus: 0.2mm² - 1.5mm²
- Protection class: IP20 II

Functions:
- Room temperature from Uponor Base or third-party KNX thermostats
- Room setpoint from Uponor Base or third-party KNX thermostats
- Room relative humidity from Uponor Base or third-party KNX thermostats
- Room floor temperatur from Uponor Base or third-party KNX thermostats
- Actuator status from Uponor Base or third-party KNX system
- Forced ECO from Uponor Base PRO or third-party KNX system
- Pump output from Uponor Base or third-party KNX system
- Boiler output from Uponor Base or third-party KNX system
- Heating/cooling curve settings/circuit from Uponor Move PRO to BMS or vice versa
- Heating/cooling modes from Uponor Base PRO to BMS or vice versa

Consisting of:
- Gateway module R-147 KNX
- Power supply
- Mounting set (2 screws and 2 wall plugs)
- Quick guide

- 6 channel slave module for Uponor Smatrix Base controller X-145 Bus 6X and Uponor Smatrix Base PRO controller X-147
- Bus 6X and Uponor Smatrix Base pro controller X-148 Modbus RTU
- Supports up to 6 room thermostats and 6 actuators
- Click-in installation
- Protection class: IP20
- Colour: grey

- Spare part touch panel for Uponor Smatrix Base controller X-147 Bus 6X
- Protection class: Class II IP20
- Colour: white RAL9016

Consisting of:
- Uponor Smatrix Base PRO interface I-147
- Power supply
- Mounting set
- Wall bracket
- Instruction leaflet

- Establishes connection between Uponor Smatrix Pulse system, Uponor Smatrix Pulse app and the Uponor cloud

- Compatible with:
- Uponor Smatrix Base controller Pulse X-245 Bus 6X
- Uponor Smatrix Wave controller Pulse X-265 6X
- Power supply: RJ45 cable to Uponor Wave or Base controller Pulse
- Ethernet interface: 10/100 Mbps (RJ45)
- Ethernet protocols: Ethernet II
- Protection class: Class II IP20
- Colour: white

- Consisting of:
- Uponor Smatrix Pulse com R-208
- Adaptor for DIN rail installations
- RJ45 connection cable (2m)
- First step instructions, safety instructions
- Mounting material

- Interface to a heating/cooling source
- Switch over H/C between Uponor Smatrix and H/C source
- Incl. socket for DIN rail mounting, manual, mounting material, wall box
- Contact: 2 change-over (CO)
- Ucoil: 230VAC
- Test voltage: 5kV
- Protection class: IP40
- Switching voltage: 380VAC, 125VDC
- Switching current: 5A@250VAC, 5A@30VDC
- Contact material: Ag+Au plated
- Temperature range: -40°C - +70°C

- Interface to a heating/cooling source
- Switch over H/C between Uponor Smatrix and H/C source
- Incl. socket for DIN rail mounting, manual, mounting material
- Contact: 2 change-over (CO)
- Ucoil: 24VDC
- Test voltage: 5kV
- Protection class: IP40
- Switching voltage: 380VAC, 125VDC
- Switching current: 5A@250VAC, 5A@30VDC
- Contact material: Ag+Au plated
- Temperature range: -40°C - +70°C